View LM158W_953644.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LM158W-LM258W-LM358W
Low power dual operational amplifiers
Features

Internally frequency compensated Large DC voltage gain: 100 dB Wide bandwidth (unity gain): 1.1 MHz (temperature compensated) Very low supply current per operator essentially independent of supply voltage Low input bias current: 20 nA (temperature compensated) Low input offset voltage: 2 mV Low input offset current: 2 nA Input common-mode voltage range includes ground Differential input voltage range equal to the power supply voltage Large output voltage swing 0 V to (VCC - 1.5 V) ESD internal protection: 2 kV Pin connections (top view)
1 2 3 4 + + 8 7 6 5
N DIP-8 (Plastic package)
D&S SO-8 & miniSO-8 (Plastic micropackage)
P TSSOP8 (Thin shrink small outline package)
Description
These circuits consist of two independent, highgain, internally frequency-compensated which were designed specifically to operate from a single power supply over a wide range of voltages. The low power supply drain is independent of the magnitude of the power supply voltage. Application areas include transducer amplifiers, DC gain blocks and all the conventional op-amp circuits which now can be more easily implemented in single power supply systems. For example, these circuits can be directly supplied with the standard +5 V which is used in logic systems and will easily provide the required interface electronics without requiring any additional power supply. In the linear mode the input common-mode voltage range includes ground and the output
1 - Output 1 2 - Inverting input 3 - Non-inverting input 4 - VCC5 - Non-inverting input 2 6 - Inverting input 2 7 - Output 2 8 - VCC+
voltage can also swing to ground, even though operated from only a single power supply voltage.
April 2007
Rev 6
1/20
www.st.com 20
Contents
LM158W-LM258W-LM358W
Contents
1 2 3 4 5 Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.1 5.2 5.3 5.4 DIP8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 SO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 MiniSO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 TSSOP8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6 7
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2/20
LM158W-LM258W-LM358W
Schematic diagram
1
Schematic diagram
Figure 1. Schematic diagram (1/2 LM158W)
3/20
Absolute maximum ratings and operating conditions
LM158W-LM258W-LM358W
2
Absolute maximum ratings and operating conditions
Table 1.
Symbol VCC Vi Vid Ptot
Absolute maximum ratings
Parameter Supply voltage Input voltage Differential input voltage Power dissipation (1) Output short-circuit duration
(2)
LM158W/AW LM258W/AW LM358W/AW +32 -0.3 to VCC +0.3 -0.3 to VCC +0.3 500 Infinite 50 -55 to +125 -40 to +105 -65 to +150 0 to +70
Unit V V V mW
Iin Toper Tstg
Input current
(3)
mA C C
Operating free-air temperature range Storage temperature range Thermal resistance junction to ambient(4) (5) SO-8
125 190 120 85 C/W
Rthja
MiniSO-8 TSSOP8 DIP-8 Thermal resistance junction to case SO-8
40 39 37 41 model(6)
(7)
Rthjc
MiniSO-8 TSSOP8 DIP-8 HBM: human body
C/W
2 200 1.5
kV V kV
ESD
MM: machine model
CDM: charged device model(8)
1. Power dissipation must be considered to ensure maximum junction temperature (Tj) is not exceeded. 2. Short-circuits from the output to VCC can cause excessive heating if VCC > 15V. The maximum output current is approximately 40 mA independent of the magnitude of VCC. Destructive dissipation can result from simultaneous short-circuits on all amplifiers. 3. This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistor becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also NPN parasitic action on the IC chip. This transistor action can cause the output voltages of the Op-amps to go to the VCC voltage level (or to ground for a large overdrive) for the time during which an input is driven negative. This is not destructive and normal output will be restored for input voltage higher than -0.3 V. 4. Short-circuits can cause excessive heating and destructive dissipation. 5. Rth are typical values. 6. Human body model: 100 pF discharged through a 1.5 k resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 7. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 ), done for all couples of pin combinations with other pins floating. 8. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to the ground.
4/20
LM158W-LM258W-LM358W Table 2.
Symbol VCC Vicm Supply voltage
Absolute maximum ratings and operating conditions
Operating conditions
Parameter Value 3 to 32 VDD -0.3 to VCC -1.5 -55 - +125 -40 - +105 0 - +70 -40 - +125 Unit V V
Common mode input voltage range Tamb = +25 C Operating free air temperature range LM158W LM258W LM358W LM258WY-LM358WY
Toper
C
5/20
Electrical characteristics
LM158W-LM258W-LM358W
3
Table 3.
Symbol
Electrical characteristics
VCC+ = +5 V, VCC-= Ground, Vo = 1.4 V, Tamb = +25C (unless otherwise specified)
Parameter LM158AW-LM258AW LM358AW Min. Typ. Input offset voltage (1) Tamb = +25 C - except LM158AW/358W Tamb = +25 C - LM158AW/358W Tmin Tamb Tmax - except LM358W Tmin Tamb Tmax - LM358W Iio Input offset current Tamb = +25 C Tmin Tamb Tmax Input bias current (2) Tamb = +25 C Tmin Tamb Tmax Large signal voltage gain: VCC = +15 V, RL = 2 k, Vo = 1.4 V to 11.4 V Tamb = +25 C Tmin Tamb Tmax Supply voltage rejection ratio (Rs 10 k) VCC+ = 5 V to 30 V Tamb = +25 C Tmin Tamb Tmax Supply current, all amp, no load Tmin Tamb Tmax, VCC = +5 V Tmin Tamb Tmax, VCC = +30 V Input common mode voltage range VCC = +30 V (3) Tamb = +25 C Tmin Tamb Tmax Common mode rejection ratio (Rs 10k) Tamb = +25 C Tmin Tamb Tmax Output current source VCC = +15 V, Vo = +2 V, Vid = +1 V Output sink current (Vid = -1 V) VCC = +15V, Vo = +2V VCC = +15V, Vo = +0.2V 2 Max. LM158W-LM258W LM358W Min. Typ. Max. Unit
Vio
1 1
3 2 4
2 2
5 7 7 9
mV
mV
10 30 50 100
2
30 40 150 200
nA
Iib
20
20
nA
Avd
50 25
100
50 25
100
V/mV
SVR
65 65
100
65 65 1.2 2
100
dB
ICC
0.7
0.7
1.2 2
mA
Vicm
0 0 70 60 20 10 12 85
VCC+ -1.5 VCC+ -2
0 0 70 60 85
VCC+ -1.5 VCC+ -2
V
CMR
dB
Isource
40 20 50
60
20 10 12
40 20 50
60
mA mA A
Isink
6/20
LM158W-LM258W-LM358W Table 3.
Symbol
Electrical characteristics
VCC+ = +5 V, VCC-= Ground, Vo = 1.4 V, Tamb = +25C (unless otherwise specified)
Parameter LM158AW-LM258AW LM358AW Min. Typ. Output voltage swing (RL = 2k) Tamb = +25 C Tmin Tamb Tmax High level output voltage (VCC+ = 30 V) Tamb = +25C, RL = 2 k Tmin Tamb Tmax Tamb = +25 C, RL = 10 k Tmin Tamb Tmax Low level output voltage (RL = 10 k) Tamb = +25 C Tmin Tamb Tmax Slew rate VCC = 15 V, Vi = 0.5 to 3 V, RL = 2 k , CL = 100 pF, unity Gain Gain bandwidth product VCC = 30 V, f =100 kHz, Vin =10 mV, RL=2 k , CL = 100 pF Total harmonic distortion f = 1 kHz, Av = 20 dB, RL = 2 k, Vo = 2 Vpp, CL = 100 pF, VO = 2 Vpp Equivalent input noise voltage f = 1 kHz, Rs = 100 , VCC = 30 V Input offset voltage drift Input offset current drift Channel separation 1 kHz f 20 kHz
(4)
LM158W-LM258W LM358W Min. Typ. Max. VCC+ -1.5 VCC+ -2 27
Unit
Max. VCC+ -1.5 VCC+ -2
VOPP
0 0 26 26 27 27 27 28
0 0 26 26 27 27
V
VOH
V 28
VOL
5
20 20
5
20 20
mV
SR
V/s 0.3 0.6 0.3 0.6 MHz 0.7 1.1 0.7 1.1 % 0.02 55 7 10 15 200 0.02 55 7 10 30 300
nV ----------Hz
GBP
THD
en DVio DIio Vo1/Vo2
V/C pA/C
120
120
dB
1. Vo = 1.4 V, Rs = 0 , 5 V < VCC+ < 30 V, 0 < Vic < VCC+ - 1.5 V 2. The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output so there is no load change on the input lines. 3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the common-mode voltage range is VCC+ - 1.5 V, but either or both inputs can go to +32 V without damage. 4. Due to the proximity of external components ensure that there is no coupling originating via stray capacitance between these external parts. Typically, this can be detected at higher frequencies because then this type of capacitance increases.
7/20
Electrical characteristics
LM158W-LM258W-LM358W
Figure 2.
140 120
Open loop frequency response
Figure 3.
20
Large signal frequency response
OPEN LOOP FREQUENCY RESPONSE (NOTE 3)
0.1mF VI VCC/2 + +125C 10M W
LARGE SIGNAL FREQUENCY RESPONSE
100k W 1k W
OUTPUT SWING (Vpp)
VOLTAGE GAIN (dB)
100 80 60 40 20 0
VCC
-
+15V VO 2k W
VO
15
VI +7V +
VCC = 30V & -55C Tamb
10
VCC = +10 to + 15V & -55C Tamb +125C 1.0 10 100 1k 10k 100k 1M 10M
5 0
1k 10k 100k 1M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 4.
Voltage follower pulse response
VOLAGE FOLLOWER PULSE RESPONSE
4
Figure 5.
Voltage follower pulse response
VOLTAGE FOLLOWER PULSSE RESPONSE (SMALL SIGNAL)
500
OUTPUT VOLTAGE (V)
3 2 1 0
OUTPUT VOLTAGE (mV)
RL 2 k W VCC = +15V
450
el
+ eO 50pF
400 Input 350 Output 300 250
0 1 2 3 4
INPUT VOLTAGE (V)
3 2 1
0 10 20 30 40
Tamb = +25C VCC = 30 V
5 6 7 8
TIME (ms)
TIME (ms)
Figure 6.
Input current
INPUT CURRENT (Note 1)
90
Figure 7.
Output characteristics
OUTPUT CHARACTERISTICS
10 VCC = +5V VCC = +15V VCC = +30V
INPUT CURRENT (mA)
70 60 50 40 30 20 10 0
VCC = +30 V VCC = +15 V
OUTPUT VOLTAGE (V)
80
VI = 0 V
1
v cc IO + VO
v cc /2
0.1
VCC = +5 V
0.01
-15 5 25 45 65 85 105 125
0,001 0,01 0,1
Tamb = +25C 1 10 100
-55 -35
TEMPERATURE (C)
OUTPUT SINK CURRENT (mA)
8/20
LM158W-LM258W-LM358W
Electrical characteristics
Figure 8.
OUTPUT VOLTAGE REFERENCED
Output characteristics
OUTPUT CHARACTERISTICS
8 7 6
V CC /2 + IO VO V CC
Figure 9.
Current limiting
CURRENT LIMITING (Note 1)
90
OUTPUT CURRENT (mA)
80 70 60 50 40 30 20 10 0
-
IO
TO VCC+ (V)
+
5 4 3 2 1
0,001 0,01
-
Independent of V CC T amb = +25C
0,1
1
10
100
-55 -35
-15
5
25
45
65
85 105
125
OUTPUT SOURCE CURRENT (mA)
TEMPERATURE (C)
Figure 10. Input voltage range
INPUT VOLTAGE RANGE
15
Figure 11. Positive supply voltage
160 VOLTAGE GAIN (dB) R L = 20k W 120 80 40 R L = 2k W
INPUT VOLTAGE (V)
10
Negative
5
Positive
0
5
10
15
0
10
20
30
40
POWER SUPPLY VOLTAGE (V)
POSITIVE SUPPLY VOLTAGE (V)
Figure 12. Input voltage range
160 VOLTAGE GAIN (dB) R L = 20k W
Figure 13. Supply current
SUPPLY CURRENT
4
VCC
SUPPLY CURRENT (mA)
120 80 40 R L = 2k W
3
mA -
ID
2
+
1
Tamb = 0C to +125C
0
10
20
30
Tamb = -55C
0 10 20 30
POSITIVE SUPPLY VOLTAGE (V)
POSITIVE SUPPLY VOLTAGE (V)
9/20
Electrical characteristics
LM158W-LM258W-LM358W
Figure 14. Input current
100 INPUT CURRENT (nA) 75 50 25
Figure 15. Gain bandwidth product
GAIN BANDWIDTH PRODUCT (MHz) 1.5 1.35 1.2 1.05 0.9 0.75 0.6 0.45 0.3 0.15 0 -55-35-15 5 25 45 65 85 105 125 TEMPERATURE (C) VCC = 15V
Tamb= +25C
0 10 20 30 POSITIVE SUPPLY VOLTAGE (V)
Figure 16. Power supply rejection ratio
POWER SUPPLY REJECTION RATIO (dB) 115 110 SVR 105 100 95 90 85 80 75 70 65 60-55-35-15 5 25 45 65 85 105 125 TEMPERATURE (C)
Figure 17. Common mode rejection ratio
COMMON MODE REJECTION RATIO (dB) 115 110 105 100 95 90 85 80 75 70 65 60-55-35-15 5 25 45 65 85 105 125 TEMPERATURE (C)
Figure 18. Phase margin vs capacitive load
Phase Margin at Vcc=15V and Vicm=7.5V Vs. Iout and Capacitive load value
10/20
LM158W-LM258W-LM358W
Typical applications
4
Typical applications
Single supply voltage VCC = +5 VDC
Figure 19. AC coupled inverting amplifier
Rf 100k W R1 10kW
1/2 LM158
Figure 20. Non-inverting DC amplifier
10kW 1/2 LM158
eO A V = 1 + R2 R1 (As shown A V = 101) +5V
CI
R1 (as shown A V = -10) Co eo 0 2VPP
AV= -
Rf
R1 10k W
C1 10mF
e
0
O
(V)
eI ~ R2 100k W V CC
RB 6.2kW R3 100kW
RL 10k W
R2 1M W
e I (mV)
Figure 21. AC coupled non-inverting amplifier
R1 100kW C1 0.1mF
1/2 LM158
Figure 22. DC summing amplifier
e1 100kW
R2 1MW
A = 1 + R2 V R1 (as shown A V = 11) Co 0 eo RL 10k W 2VPP
e2 e3 100k W 100kW 100kW e4 100kW 100kW
1/2 LM158
eO
CI
RB 6.2kW eI ~ R3 1M W
R4 100kW
V CC
C2 10mF R5 100kW
eo = e1 + e2 - e3 - e4 where (e1 + e2) (e3 + e4) to keep eo 0V
Figure 23. High input Z, DC differential amplifier Figure 24. High input Z adjustable gain DC instrumentation amplifier
R1 100k W
R2 100kW R1 100kW
1/2 LM158
R4 100kW
e1
1/2 LM158
R3 100kW
R4 100kW
R3 100kW
1/2 LM158
R2 2k W
Gain adjust
1/2 LM158
eO
R5 100kW
+V1 +V2
if R1 = R5 and R3 = R4 = R6 = R7 eo = [1 + 2R1 ] ((e2 + e1) ----------R2
Vo
1/2 LM158
e2
R6 100k W
R7 100kW
if R1 = R5 and R3 = R4 = R6 = R7 eo = [1 + 2R1] ((e2 + e1) ----------R2
As shown eo = 101 (e2 + e1) As shown eo = 101 (e2 + e1)
11/20
Typical applications
LM158W-LM258W-LM358W
Figure 25. Using symmetrical amplifiers to reduce input current
1/2 LM158
Figure 26. Low drift peak detector
I eI IB
I
IB
eo
IB
1/2 LM158
2N 929 0.001mF
eI ZI
1/2 LM158
IB C 1mF 2I B
eo Zo
IB
IB 3MW IB
1/2 LM158
2N 929 2IB R 1MW
0.001mF IB 3R 3MW IB
1/2 LM158
Input current compensation
1.5MW
Input current compensation
Figure 27. Active band-pass filter
R1 100kW C1 330pF R2 100kW +V1
1/2 LM158
R5 470kW
1/2 LM158
R4 10MW C2 R3 100kW 330 pF
1/2 LM158
R6 470kW Vo R7 100kW VCC R8 100kW C3 10mF
12/20
LM158W-LM258W-LM358W
Package mechanical data
5
Package mechanical data
In order to meet environmental requirements, STMicroelectronics offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics trademark. ECOPACK specifications are available at: www.st.com.
13/20
Package mechanical data
LM158W-LM258W-LM358W
5.1
DIP8 package
Dimensions Ref. Min. A a1 B B1 b b1 D E e e3 e4 F I L Z 0.44 3.3 1.6 0.017 8.8 2.54 7.62 7.62 7.1 4.8 0.130 0.063 0.38 0.7 1.39 0.91 0.5 0.5 9.8 0.346 0.100 0.300 0.300 0.280 0.189 0.015 1.65 1.04 Millimeters Typ. 3.3 0.028 0.055 0.036 0.020 0.020 0.386 0.065 0.041 Max. Min. Inches Typ. 0.130 Max.
14/20
LM158W-LM258W-LM358W
Package mechanical data
5.2
SO-8 package
Dimensions Ref. Min. A A1 A2 B C D E e H h L k ddd 0.1 5.80 0.25 0.40 1.35 0.10 1.10 0.33 0.19 4.80 3.80 1.27 6.20 0.50 1.27 0.228 0.010 0.016 8 (max.) 0.04 Millimeters Typ. Max. 1.75 0.25 1.65 0.51 0.25 5.00 4.00 Min. 0.053 0.04 0.043 0.013 0.007 0.189 0.150 0.050 0.244 0.020 0.050 Inches Typ. Max. 0.069 0.010 0.065 0.020 0.010 0.197 0.157
15/20
Package mechanical data
LM158W-LM258W-LM358W
5.3
MiniSO-8 package
Dimensions Ref. Min. A A1 A2 b c D E E1 e K L L1 0 0.40 0.55 0.05 0.78 0.25 0.13 2.90 4.75 2.90 0.10 0.86 0.33 0.18 3.00 4.90 3.00 0.65 6 0.70 0.10 0 0.016 0.022 Millimeters Typ. Max. 1.1 0.15 0.94 0.40 0.23 3.10 5.05 3.10 0.002 0.031 0.010 0.005 0.114 0.187 0.114 0.004 0.034 0.13 0.007 0.118 0.193 0.118 0.026 6 0.028 0.004 Min. Inches Typ. Max. 0.043 0.006 0.037 0.016 0.009 0.122 0.199 0.122
16/20
LM158W-LM258W-LM358W
Package mechanical data
5.4
TSSOP8 package
Dimensions Ref. Min. A A1 A2 b c D E E1 e K L L1 0 0.45 0.60 1 0.05 0.80 0.19 0.09 2.90 6.20 4.30 3.00 6.40 4.40 0.65 8 0.75 0 0.018 0.024 0.039 1.00 Millimeters Typ. Max. 1.2 0.15 1.05 0.30 0.20 3.10 6.60 4.50 0.002 0.031 0.007 0.004 0.114 0.244 0.169 0.118 0.252 0.173 0.0256 8 0.030 0.039 Min. Inches Typ. Max. 0.047 0.006 0.041 0.012 0.008 0.122 0.260 0.177
17/20
Ordering information
LM158W-LM258W-LM358W
6
Ordering information
Temperature range
Part number LM158WN LM158WD LM158WDT LM258WAN LM258WAD LM258WADT
Package DIP-8
Packaging Tube Tube or tape & reel Tube Tube or tape & reel Tube Tube or tape & reel Tube
Marking LM158WN 158W LM258WA 258WA LM258WN 258W LM358WN 358W
-55C, +125C SO-8 DIP-8 SO-8 -40C, +105C DIP-8 SO-8 DIP-8 0C, +70C SO-8 Tube or tape & reel 358AW TSSOP-8 Tape & reel K411
LM258WN LM258WD LM258WDT LM358WN LM358WD LM358WDT LM358AWD LM358AWDT LM258WYPT (automotive grade)(1) LM258AWYPT (automotive grade)(1) LM258WYD LM258WYDT (automotive grade) LM258AWYD LM258AWYDT (automotive grade)(1) 40C, +125C LM358WYD LM358WYDT (automotive grade)(1) LM358AWYD LM358AWYDT (automotive grade)(1) LM358WYPT (automotive grade)(1) LM358AWYPT (automotive grade)(1)
(1)
TSSOP-8
Tape & reel
K410
SO-8
Tube or tape & reel
258WY
SO-8
Tube or tape & reel
258AWY
SO-8
Tube or tape & reel
358WY
SO-8
Tube or tape & reel
358AWY
TSSOP-8
Tape & reel
K412
TSSOP-8
Tape & reel
K413
1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q 002 or equivalent.
18/20
LM158W-LM258W-LM358W
Revision history
7
Revision history
Date 1-Nov-2002 1-Jul-2005 Revision 1 2 First release. ESD protection inserted in Table 1: Absolute maximum ratings on page 4. ESD tolerance for model HBM improved to 2kV (Table 1: Absolute maximum ratings on page 4). Rthja and Rthjc typical values added in Table 1: Absolute maximum ratings on page 4. Added Figure 18: Phase margin vs capacitive load on page 10. Order codes added (automotive grade level) to Section 6: Ordering information. Previously called revision 4. Footnote for automotive grade order codes added to Section 6: Ordering information. Added missing Revision 4 of January 2007 in revision history. Corrected revision number of March 2007 to Revision 5. Changes
6-Oct-2006
3
2-Jan-2007
4
15-Mar-2007
5
25-Apr-2007
6
19/20
LM158W-LM258W-LM358W
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
(c) 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
20/20

▲Up To Search▲

Price & Availability of LM158W

	To Download LM158W Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .